Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I m using nrf52840 and m doing DFU over serial.
one side is master controller and other end is NRF DFU serial(secure bootloader uart debug code).
After sending init...
Hi everyone,
I am trying to connect to a smartphone in an extended advertising using the firmware created under the following conditions. However, there are no event notifications...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am making an example of periodically reading sensor data using SPI.
The SPI is triggered through...
Currently I am using a PCA10040 to do some prototyping for a custom board. I intended to use the nrf52832 to interface with a HDC2010 (TI) temperature and humidity IC over...
Hi,
I was using SDK v1.1.0 for a while and am updating my project to SDK v1.2.0. I see that there is also a release for v1.3.0, however, there are too many application and...
I have tried to setup the time cluster, with:
ZB_ZCL_TIME_SET_REAL_TIME_CLOCK_CB(time_set_rtc);
But whn I do it, I lways get linking errors, since zb_scl_set_real_time_clock_callback...
I had a continuation question to this.
https://devzone.nordicsemi.com/f/nordic-q-a/64457/scheduler-for-thingy-91-using-nrf9160-dk
Is there any sample tutorial for the...
I don't think this is possible at the moment but worth putting it out in the wild:
Currently the binary image sizes for nRF9160 using Zephyr can get quite hefty. Is there...
Hi All,
I am looking for some working example/reference nRF Mesh project where I can get the temperature and humidity values from Thingy device. If someone can help me out...
I trying to connect with ble, i was setup MyBleManager extend BleManager and initialize with the default values it requires but i haven't declare and add UUID in BleManagerGattCalback...
I'm trying to set up the Dongle pca10059. I'm using the softdevice 140 and segger studio. The code is from the SDK, the template example.
the main.c:
static ble_uuid_t...
Hi,
I would like to know if there is an event from peripheral side to indicate that the discovery process is over.
The gold is to disconnect from the central if all the...
1.Would you please confirm the maximum ripple range that nrf52832 can accept for VDD (3.3V) and dec4 (1.3V) power supply, that is to ensure that the function will not be affected...
Hello,
I have used the Nordic Thingy application, I also used the Raspberry Pi Python interface and I observed the temperature measured.
The temperature is not stable...
