Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi. I use sdk16 and ble sample like kb or mouse. i want to save some data in ic. with flash_fstorage.
i see flash_fstorage example .it can use SOFTDEVICE_PRESENT for save...
Hello,
I am trying to find a way to upload the certificate automatically from the main.c file instead of uploading them to LINK monitor. Is there a command in nrf project...
I have a known working distribution (ZIP) file that when flashed onto a device, correctly goes into the application and is able to do buttonless DFU. This was left behind...
hi all:
NRFSDK_16. I want to get timestamp from rtc,but my device need run with low power,so when the device in idle mode(no user use),will put it in system off mode.
...
Hi, Nordic,
I have the follow questions in the nRF5_SDK_17.0.0_9d13099
1. Why in the Demo ble_app_multirole_lesc remove the BLE_GAP_EVT_LESC_DHKEY_REQUEST's process as...
Like --insecure option in the curl command, i want to skip certificate validation when make a https connection to server, so i have checked all http files in zephyr and there...
Hi everyone,
I am new to programming on such an embedded device(NRF52840DK). I met a problem recently of how to set up the PIN on the board to connect with the LPS22HB sensor...
According to the doc; * This function will block until the temperature measurement is done. * It takes around 50 us from call to return.
Instead I'd like to return the value...
Hi,
I’m developing an application using the SDK V16 , the nRF52DK (52832) as central, and a couple of Sparkfun nRF52832 breakout boards as peripherals (both peripherals...
Hi everyone!
I am trying to implement the OTA - DFU in my project. I have my own board with a nrF52832 chip.
The project was build using SDK 13.0.0 and softdevice s132...
Dear Nordic Support Team,
I was using the CoAP and MQTT components in nRF5 SDK v16.0 .
So my device was able to do CoAP and MQTT via BLE 6LoWPAN. Adding a BLE service...
I am following the turtorial in the Github and build a project which add a custom service. The project can read, write and notify between the board and mobile nRF connect...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board.
I am using the UART module and associated UART drivers.
Is there a way to ignore the...
I have two nRF9160 DK boards that are programmed with modem firmware version 1.1.1 and are using V1.2.0 sdk software. They also are both programmed with the same mqtt_simple...
