hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi, what is the impedance of the nRFM9160 GSM antenna?
I'm asking because I'm in the process of verifying the tuning on an antenna + LNA circuit. We will most likely tune...
I am using nrf52832. I am making custom board file .I am little bit confused which function are used for set the pin as output or input.
__STATIC_INLINE void nrf_gpio_cfg_output...
Hi All,
from below post, I found that in SDK11, bootloader code uses NRF_UICR->CUSTOMER[0] register for device type and revision verification so application should not use...
Hi
This is Joe. I would like to ask questions about implementing BLE bonding.
SDK: 16.0.0 (nRF5SDK160098a08e2)
Projects: The base project I start with is NUS example...
Hello,
I am trying to develop BLE custom board. It's my first time dealing with Nordic MCUs and RF. I want to understand if I am doing it all correct. Here is a piece of...
Hi,
In the I2C communication,the nRF52840 SoC is master, the sensor SCD 30 is slave. The sensor SCD 30 needs the clock stretching period, the period time is 12ms or 150ms...
Hello,
I have a general question for you.
When we develop an application from one of your examples and then you put online a new version of your SDK, do you have any advice...
Hello, I am using the nrf9160 DK and connected it with a SIM card of a local provider. The SIM card is able to connect to the LTE network and NB-IoT.
For researches I only...
Hi, I am developing a multi-link central using NRF52832 and SDK 16. I have implemented the scanning part and NRF_BLE_SCAN_SCAN_DURATION = 0. I am using address filter for...
Hi Nordic Team,
I know there are many tickets raised concerning this error 133. It is a quite generic issue with Android devices of various android versions and I have gone...
Hi, I have a problem find bluetooth device on more android phones after them unpair.
First time phones find device and connect but after unpair phone not find devices. ...
I want to make printf_test.c file into a lib file and join my nrf9160 routine, but don't know how to generate the lib file and how to join the lib file?
The measured project...
Hi everyone,
I'm using the nrf5_SDK_for_Mesh_v4.1.0 and i'm having troubles by trying to change the BLE name.
In the function gap_params_init i added a code to concatenate...
