hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I'm trying to use this API: NRF_STATIC_INLINE void nrf_rtc_subscribe_set(NRF_RTC_Type * p_reg, nrf_rtc_task_t task, uint8_t channel) to set DPPI subscribe configuration for...
Hello, I'm Jongryul
I want to deliver voice through BLE.
I wonder if this chip supports voice command.
If this chip does not support voice command, I wonder about the...
I'm trying to create a siren tone using the pwm library, that ramps up and down between 2kHz and 3kHz.
Initially I started with the example provided in SDK v15.3.0 nRF5_SDK...
hello community!
Recently I got urgent job to rewrite sensor firmware to nrf52832.
Its not my project basically, another company project.
I wonder why rf52832 didn...
I understand with LTE-M they are supposed to offer greater distances to the cell site, but how do we tell how far away we are from the cell? In the good ol' days, we could...
It says under the S113 information that is supports extended advertising yet I can't see it in the API. I would like to take advantage of the 255 byte advertisement size for...
I want to use NRF9160 for development, now I want to pick something bootloader, so which one do I use
1. \ zephyr, replication, bootloader, McUboot \ zephyr
2. \ zephyr...
I am trying to develop a product with your nRF905. I have two units set up, and can read and write via SPI. However my concern is your poor documentation.
You do not say...
Hello, this is the person who asked about " devzone.nordicsemi.com/.../question-serial-output-uart ". First of all, thank you very much for your sincere reply.
The reason...
Hello
I would like to view the changes in sensor values in real time in a graph. Can you recommend a tool from Nordic or an easy-to-use program?
Thank you.
Sometimes during a DFU update, the NRF52811 can stay in bootloader mode (seen with name DFUTarg and mac_address equal to mac_address +1). I am on Softdevice 16.0 I'm using...
How to read values from 5 Analog pins at the same time
I know how to read from one Analog Pin, but i don't know how to access 5 analog pins at the same time and display...
Hello I am developing a prototype with the Thingy 91 that allows to have the default log in the UART0 <-> USB and collect the data of a sensor through the P6 expansion port...
I have a custom board using NRF52832 which communicates with a BMI160 accelerometer/gyroscope chip by SPI.
I have been developing in Segger Embedded Studio (v5.10d) in debug...
Is the nRF52840 sniffer is support to capture, decrypt and analyze the mesh specific data?
currently, BLE based sniffers can only able to saw a advertise data without any...
