I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I am using
PCA10056
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am testing background serial-dfu.(refer to https://devzone...
Hello,
We are working with the nrf 9160 dk.
We need to use internet connectivity to send an http get and post to a remote server.
We want to utilize the NB-IoT...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
I use nRF5_SDK_15.0.0
My soc is NRF52832,project is based on ble_peripheral ble_app_blinky.
After I call idle_state_handle() let my device go to sleeping.
Sleep current...
Hello,
We are using nrf52832 with sdk 16.0, for a particular reason we are storing some variables in flash storage, i have some question regarding that
what is the time...
Hello,
I am developing a driver that can handle cryptographic operations and I am using example code from nRF5_SDK_16.0.0_98a08e2 /examples/crypto/nrf_cc310/aes to get...
I have a Segger J-Trace Pro and am attempting to enable trace debugging of my application. I have a custom board that breakout out the appropriate Trace Clk and Trace Data...
Installed nrfutil with python 3.8 and pip3 20.0.2 on Windows 10 Trying to run dfu over usb-serial: nrfutil dfu usb-serial -pkg FW.zip -p COM4 -b 115200
I get the following...
Hello,
I got a problem with the nRF sniffer for Wireshark. I got the following configuration:
Board: nRF52-DK pca10040
Hex file: sniffer_pca10040_129d2b3.hex (provided...
Hello:
nRF52840 UART peripheral receiver FIFO reset
Whenever there is a receiving error ( Frame error or Break error or any) , I would like to reset the receiver's FIFO...
I have an application that requires mains power for lighting with a BLE receiver that is permanently advertising and scanning and I need to be able to dim the lights. My circuit...
Hi
I am new to nordic processors.
I am using spi_ pca10040 project as a reference for my custom board. On my board the SPI pin configuration is different from pca10040...
I understand the reason for the polygon cutouts under component pads in the RF nets in nRF9160 DK design (and others). However, at LTE and GPS frequencies this doesn't seem...
