I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi, I'm a ble developer using nrf51822.
It is a wierd question,
Is this any possible to write value to one characteristic's CCCD value from itself(device)?
This is my...
I am using the nRF51822 Development Kit
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v5.2.0.39364.
I am unable to program the SoftDevice...
Are there any I2C examples for the nRF51822 ( write/ read functions) ?
If not, can anyone suggest a good starting point for I2C?
I am using Eclipse kepler for development...
In the nRF51 SDK examples, some pass the parameter adv_params off the stack as a locally declared vaiable in the context of the function and some pass static global variables...
I successfully made an Arduino code using nordic library that gets notification from iOS ANCS.
But some minor bug exists: sometimes i don't get any notification from the...
Hi all,
I used the ble_app_hids_mouse example in SDK 4.4.1 and found:
1.when the mouse does the first bonding with the master, the report rate could reach 125Hz(I set...
Hi, I am trying to code my nRF51822 on my custom board, however right now I'm having my doubt on using some of the example code provided in the SDK.
Essentially, I want...
Hi,
1/ I download the s110 softdevice and ble_app_hrs to the nRF51822 board, and running normally.
2/ I download the s120 softdevice and ble_app_hrs_c to the nRF51822...
Dir sir. I read the white paper "Tuning the nRF24xx matching network" and I have a question.
I would like to know the setting of the spectrum analyzer when I measure the...
I'm looking at the 5.2 SDK and I have noticed a few minor things that may be bugs or might be my mistake but here goes:
In the GCC linker scripts, I was carefully...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am working on a keyboard project,I change the HID report as follows
0x05, 0x0C, // Usage Page (Consumer Devices)
0x09, 0x01, // Usage (Consumer Control)
0xA1...
Hi,
How does the advertisement filter policy work?
I tried both BLE_GAP_ADV_FP_FILTER_SCANREQ and BLE_GAP_ADV_FP_FILTER_BOTH, but this doesn't restrict other devices...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
