Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
Looking at the code of function nrf_log_frontend_dequeue, in nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c:716, it seems to me that the code chunk...
Hello!
I'm trying to implement a thermostat cluster handling. I've managed to implement read/write thermostat attributes handling using zigbee device callback. The problem...
I am trying to design a remote control for my garage door and I need to develop a low power remote control that talks to my Thread garage receiver.
I have looked into OpenThread...
Hi, I am attempting to flash various bluetooth samples onto the nRF5340pdk, and I am getting errors on multiple levels.
First, when I attempt to build the samples (I have...
Hello, I am trying to load some example on my nRF52840 dongle. I am developing without using a board but only the dongle, SEGGER and nRF Connect 3.6.0 .
Following this guide...
Hi everyone,
I've noticed in SDK examples such as the ble_app_hrs that call APP_ERROR_HANDLER after softdevice API Call.
What is the reason for this API call?
Any side...
Hello,
I am working on ble_app_uart example on nRF52840DK.
According to the documentation, when the device is advertising, the LED1 should blink. But I am not able to...
Hi all,
I was going through the release notes of the S132 V7.2.0.
Under known issues, DRGN-10340 states the following:
"The BLE_GAP_EVT_SEC_INFO_REQUEST event will not...
