It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
This is the third time attempting to install nRF Connect SDK on my Linux box at home, and have failed at the same place every time. I followed all the instructions while using...
Dear Support Team,
We are migrating our designs to nRF52820. With previous IC we saw that Johanson has IPD for atenna filter + matching circuit (e.g.2450FM07A0029), but...
Now we have a new project,in order to long distance communication,we add a PA RFX2411N in our design,now how may I tuning the pi (or T) match network between nRF52 chip and...
Hi All, What is the best way to modify ble_app_multilink_central and ble_app_blinky example codes, so BLE tag can send to ble_app_multilink_central Its own address. The ble_multilink...
My application uses a NRF52 (SD132, SDK 15.0.0), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
Hi, I'm having some issues with migrating from SDK12.1 to SDK16 while discovering services.
It seems to connect to Android without much issue, but on iOS the connection...
A project is currently utilizing an NXP module to access the SD card via 4-bit SDIO. I am exploring the feasibility of integrating an nRF52840-based module, and have a few...
I am trying to use the battery example in " /ncs/zephyr/samples/boards/nrf/battery" to measure my 3V coin cell via VDD. I am using P0.14 to enable a set load on VDD before...
I'm using a nRF52840 DK (PCA10056 2.0.1 2020,14 683193023) with an adafruit FTDI serial TTL-232 USB cable (part number P70C uses the FTDI -FT232R chip inside a translucent...
i use pca20023-sr3_nrf52832_product_example demo to test, but there was an error occued , the segger rtt views displays:
00> [00000000] <info> app: System ON 00> [00000000...
Hello,
I'm in the process of developing the HW board for a nRF5340-based product. I need the customer could update the firmware using a serial port (USB or Bluetooth is...
I am testing a number of boards with a QSPI memory module with NRF52840 chip.
The QSPI driver functions all return without error even if the chip is not present. What is...
I have made PCB 32mhz crystal footprint with error. I have used other khz frequency too. Now I can't solder 32mhz crystal is it possible to code nrf52832 and control various...
Hello,
I wanted to test the long range, so changed the primary and secondary PHY to BLE_GAP_PHY_CODED from BLE_GAP_PHY_1MBPS in the advertising_init() of the peripheral...
