Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello
I want to install the nRF Connect SDK (v3.4.1) on my Linux Elementary OS 5.1.6 Hera to use the nRF9160 and the Thingy91 later on. I've installed the toolchain and...
Hey,
I am working on S130, nRF51, been working for a long time with DFU and it was fine both using nRF Connect and nRF Toolbox
Lately I changed my workstation and so...
Hello everyone I am trying to program my dongle with the Dk Following this schematic :
When I press the reset button on the dongle, the led start pulsing in red.
I am...
someone that can give me a datasheet of this microcontroller (i think) i searched the hole web and don't find one in specific, the one i found are different in the last line...
Hello, I am working on low power modes of MCU M33 core in nRF9160 SOC.
From the document of nRF9160 product specification v1.0, understood that there are two low power modes...
Hello,
I am trying to capture the advertisements of the surrounding BLE devices with NRF52840 Dongle using pc_ble_driver_py python library. I am successful in capturing...
I am working on third party module RAYTAC MDBT50Q-DB with nRF52840 with SDK V17.0. I am trying to run ble_app_interactive example on it but just can't get it done. I have...
Hello,
I'm using the light_switch example for my application and I've integrated my custom model into it. I want to learn which address the server and client respond/publishes...
Hello,
I want to give user defined hard-coded OOB Number in this example for generic on-off Client-Server code, for provisioning both client and server node ( nrf52 DK ...
Hi,
We use mdbt42v(nrf52832) to design a custom board and we encounter a strange issue.
We use ain2(P0.04) to measure a Variable Resistor value, the code working fine...
Hi,
I am using an NRF52832 device (Peripheral) and I have a requirement to transmit around 4kb of data every 100 ms to a Central.
Can you recommend the correct example...
Hi,
I tried building both with cmd line and SES but I get always this error:
/usr/local/bin/cmake -GNinja -DBOARD=thingy91_nrf9160ns -DBOARD_DIR=/Users/dariofanciullo...
Hi,
I am using nrf52832 to connect 500 nrf52810, among which NRF52832 is central and nrf52810 is peripheral.
How should I do for nrf52832 based on SDK 16.0.0.
