I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
Hello,
I am trying to use "west" command in Eclipse but I am not able to do it.
I was able to do that in Visual Studio though.
I found this link https://devzone.nordicsemi...
Hi,
We are trying to configure the WDT and are running into issues. The plan was have a timeout of 30 seconds when running and then 24 hours when sleeping. Note we are...
While developing the power supply for edge cases of NRF9160-SIBA we encountered problems with both the continuous and peak current consumption, mostly during startup. We are...
I have a question on stack guard that I tried to enable on nRF52840 and hope you can give me some pointer to verify it is functioning properly.
Basically, I call nrf_stack_guard_init...
Hello i am making an application using hid over gatt. i changed original keyboard usb description with fido description for test, however, i don't get any event through. I...
the link i given below tells, how to make a haptic glove using arduino mega
https://hackaday.io/project/160405-diy-haptic-glove-for-vr
i want to do it with nrf52840 DK...
Hi everyone,
I'm working on programming nRF52833. I want to my nRF52833 is able to broadcast advertising and also scanning (In another word, my device plays peripheral role...
Hi
I have upgraded from an early version of SLM to the latest version in nRF Connect SDK ver. 1.3.1
the SLM application is running on a custom board with a nRF52840. Using...
I found this application very useful!!
The code is now at the Github.
I found there are some problems to reconnect - it gets many errors and the peripherals eventually...
Hi, I understand there's no high level TWIS (i2c slave) driver for nRF9160 (i.e. in Zephyr); as such, I need to use TWIS driver that's part of nrfx, or even lower (HAL) level...
Hi,
I need to upload compiled binaries from mbed studio to my custom board based on nrf52840 using nrf52840 dk.
I have replaced the jlink software( J-Link OB-SAM3U128...
