I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
Please understand my low English level.
Segger cannot find be_advdata.h. I've added this route to the preprocessor. But an error occurs. How can I fix this?
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
For better clarity, I am trying to understand...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
Hi
We are using the nRF9160 to drive the SD pin of the QM14501 LNA, which would typically consume 740uA. While the pin is driven high, I only measure 0.7V on the pin, so...
Hello,
I'm receiving a FDS_EVT_UPDATE (FDS_ERR_OPERATION_TIMEOUT) in my fds event handler. My update didn'it work but i don't know why.
If someone has already faced this...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
hi, I am beginner , so confused how to doing write and read sequence. I want read and write sequence with register setting .please give me how to develope logic for that.
Hi,
I'm working on a BLE link between two dev kits. For the time being, both have USB drivers and handlers that will pipe data from one USB terminal to another over BLE...
I'm having a bit of trouble getting a program downloaded onto my development board. I've been using Keil 5 to program and I haven't had a problem until I started experimenting...
