I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm working on an nRF52840 design where we may get away with only the outer pin row on the package.
However, one pin on the inner row of harder to reach pins seems important...
To the kind attention of Nordic support team,
I'm considering here a scenario where only a device and only an host PC are involved. They are ble bonded together.
Now,...
I have been working on receiving data from sensor using nrf52832 and I have been successful in getting the data and printing the same in the app. I have also been succesful...
Hi!
I am using an ASXL375 accelerometer with a nRF52832, and I am trying to figure out a good way to read the sensor data asynchronously (allowing the other processes the...
Hi,
I am using SDK 16 and nrf52810 pca10040e. I tried to build the example code for nrf52810 bootloader from the nordic example folder(examples/dfu/secure_bootloader/pca10040es112_ble...
Hi there!
I'm in the process of migrating a project from a nRF52832 to nRF52840 due to insufficient memory and of course some problems arise during the process. Most of...
There is a bug on the nrf_ble_scan.c uuid 128 bit filter. My devices advertise the same 128bit uuid service, which is constituted of my random generated 128 bit UUID and a...
Hi,
I am aware that when the the modem is powered down with AT+CFUN=0, GPS data such as the ephemeris is saved to flash. What endurance does this flash have? How many times...
nAN_38 gives UBM dia as 155um for nRF51 WLCSP parts.
The devzone gives 180um for nRF52840.
What is UBM diameter for nRF52832, nRF52833, nRF52810 and nRF52811?
Best regards...
Dear Community;
We are trying to implement HTTP application update with our own server. We have flashed the "http_application_update" project to an nRF9160. It works fine...
Hi, first of all I want to thank you all for this forum which helps me a lot during the develop and apologize for my english.
I am developing an application on nRF52832...
Hi guys, i'm working on mobile app for ios, base of my code is example from this github repo https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library
if i understand...
The SIM "893..." is already linked to your account. Then i skip this step and trying to add the LTE to my account. But always this error: "There was an error adding your device...
No available samples initiate the non-secure CPU (CONFIG_SPM = y) the secure cpu is loop!
Zephyr master NRF master
Help me please!
The test consists of running a simple...
Hi there,
we're using nrf52840 with the nRF SDK version 16.0.0. The device is using the SD and the FreeRTOS. The SD version is s140_nrf52_7.0.1.
At a certain event (out...
