Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
What is the fast way to stream data from NRF52840
1) Using USB interface and virtual com (CDC)
2) Using UART interface and extenal converter as DTFI
Please Advise...
Hi,
I use SDK16 and S140 softdevice v7.0.1. I try to send a binary file from mobile to nRF52840 (PCA10056). I download examples\ble_peripheral\experimental\ble_app_ots project...
Hey Guys,
I am trying to send a mesh message to a group address using nRFMesh application in IoS. After accessing the Groups tab, it is showing as "No models configured...
Hi there, I'm trying to build the IOS-nRF-Toolbox, with the hope of using it as the basis of our app. But, I cannot build it with the following errors:
/Users/admin/Documents...
I know there is Current consumption common conditions in the datasheet. (table19. nRF9160_PS_v1.2.pdf)
There is VDD level but It's not described the VDD_GPIO level.
1...
Hi,
I am following the tutorial https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/getting-started-with-nordics-secure-dfu-bootloader...
Hello,
I really find this tutorial useful and substantial. I followed the steps in downloading the github projects but I got the following errors when compiling (Note: I...
Greetings everyone,
I am a beginner in this and would like to ask for help in reading battery level.
Battery info: 3.7V, 100mAh, 0.37wh.
I have tried to read on the...
hai ,
i my application i need to update ota over serial . i m using nrf52840 and sdk 15.2
step 1 : at first flashed uart boot loader code on my board
step 2 : updated...
Hello
I am testing connection between nrf51 dongle and my BLE keyboard using heart_rate_collector sample.but there is an issue with on_service_discovery_response.
my BLE...
Does exist any IC/module of Nordic which could be used as NFC reader/initiator and that has BLE integrated also?
Or just a little BLE module with on-board uFL connector...
Hi Devzone:
We are testing TX and RX range with our customized boards, and encountered a rather bizarre problem:
The connection range is pretty good indoor, maybe 20~30...
I am working on a driver for the Adesto AT25QL641 QSPI Flash Memory chip. Comparing the hardcoded nRF52840 QSPI instruction set and the AT25QL641, they are 90% identical except...
