I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am using pc_ble_driver_py package to test BLE for my proejct with nrf dongle
I need to get rssi in dongle side and I found ble_gap_rssi_start and ble_gap_rssi_stop...
Hi,
Is it possible to write/read the flash memory, from within the interrupt handler of GPIO? I used an push button connected to a GPIO to wake up the ble chip, then read...
Hi,
Does nRF5340 (or any other nRF52XX) support natively ISO7816-3 (SmartCard)?
"Natively" means using USART or any other way(hardware of official software) other than...
I am reading the PPI Example at the Infocenter as shown by the link below: -
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Fppi_example...
Hello Nordic,
I worked with the interactive PyACI during several months by using my PC (running the interactive PyACI) connected through usb to a DK used as provisioner...
Hello,
We've recently migrated from SDK version 15.2.0 to 17.0.0 and noticed an anomaly with the clock driver. If the watchdog is started, then after any soft reset (through...
Hello! How can I measure the heap size (total and free space) at runtime?
Right now I'm working with some legacy code that makes a call to mallinfo()
That call returns...
I am testing "nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\experimental\ble_app_cli" example.
Do I need 2 boards to run this example ???
What I got from the infocenter...
Hi
I am using SDK17. I am running the app_pwm example and i get an error with the "nrf_drv_state_t", it is not defined and the "NRF_DRV_STATE_POWERED_ON" is not defined...
Hello,
I'm programming nrf52 with SDK17. My application requires to advertise in 1 channel and also scan in 1 channel too. I have done the code. But when I run the code...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
