I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I'm using nRF52811 and It works with 1.8 voltage on it's VCCs. Is it possible to use a micro SD? Should I use a voltage level translator (for example TXB0108)? I know...
Hello all,
I try to import Keil project into Eclipse with Makefile. I managed put all my source file to be compiled, and my include paths etc.. in my Makefile
In Keil...
Hi,
I am working on one application in which I want to sample ECG at 1000 samples per second continuously and battery value at 15 seconds interval. I am configuring two...
Hi,
I'm trying to connect my phone ober BLE with the nrf52840. The first x attemps always work (connect, disconnect, connect, disconnect, ...) but after some time no further...
Hello guys,
I`m pretty new in socket programing, I have a question , is there any way to trigger an event for a file descriptor that is used in poll() function ?
For example...
Hello DevZone,
Recently I've been testing connecting multiple servers to one client and fiddling around with some settings regarding timing and packet size.
In the following...
Hi everyone,
Recently, I have bought two nRf52 DK, and I want to test the latency between central and peripheral in 2Mbps.
Can someone give me some suggestions about where...
I develop BLE Beacon device using nRF52832. I want to set the device name by combining "XXXX" and the lower 3byte of MAC Address. "XXXX" is used to recognize it as a company...
Hi,
I have a modified template of the ble_app_template example from sdk 15 NRF58240-dk pca 10056 s140.
I have written a custom function as per this tutorial : https:/...
Hi,
I followed the "Getting Started Assistant" to setup SEGGER Embedded Studio, but after opening the GPS example for nRF9160 i end up with Import Errors. 1> main.c:8:10...
My production app(sill in development technically but pre-production stable) is having issues with our SDK14.2 BLE UART application. When the generic version from examples...
I tried to add spi driver to existing BLE project but I've got this error:
../nRF5_SDK_current/integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
Is there some way to configure nrfutil to produce the *.dat and *.bin files as such, without bundling them into a zip file? I tried going through the help and did some quick...
Hello, I have decided to use an external RTC ( M41T64) to wake up the nRF52832 from system OFF mode. I am also planning to use the RCT to generate generate the 32.768 kHz...
