Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Now I can only download the 《nRF52810 product brief.pdf》 . The link is shown below:
https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52810/GetStarted...
Hi,
I am using nRF52832 for my project. I want to perform secure connection using numeric comparison.
I want to know how six digit passkey is generated by the softdevice...
Hi,
For the testing purpose, I would like to send a few basic packets from LTE Link Monitor on nRF9160 DK to our cloud. I found a way how to do it through the nRF9160: Serial...
Hello guys,
We are developing our IoT prototype with Thingy:91 board using v1.2.0 tag.
One of the things we need to to is as follows:
Scan the BLE area looking for...
Dear Nordic
In ble_advdata.c of nRF5_SDK_16.0.0_98a08e2 , with the function:
I think parsed_name_len < strlen(p_target_name) should be parsed_name_len <= strlen(p_target_name...
After the update from the SD4.0.2 to the SD6.1.1 (nrf52832), it is not anymore possible to pair with the OnePlus5 (Android 9.0) With the Galaxy Note8 (Android 9.0) it works...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
want to add UART communication to nRF52832 with mesh enable.
I have added,
nrf_drv_uart.c
nrfc_prs.c
nrfc_uart.c
nrfc_uarte.c
files into nRF_Drivers folder...
