I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to merge Softdevice, bootloader, bootloader setting and application. But unable to do in a single mergehex command. If i do merge seperately ((BL + SD + APP) with...
Hello.
This function from Zigbee SDK 4.0.0 changes configuration of already configured input pin by calling nrf_gpio_cfg_default(ERASE_PIN);
The leds_buttons_init()...
I loaded up pca10056e ble_app_beacon example for SES to test it on a custom nrf52811 device I have built (using BMD-360 module).
I followed the instructions here and removed...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I want to know the life of FLASH by garbage collection. Assume that garbage collection is performed only when "PM_EVT_STORAGE_FULL...
the python package is not updated through pip with last release of SD_API and corresponding hex files.
I know that you give instruction to build driver but it could be easier...
I am trying to test a simple non-connectable BLE adverstising. I am using the following resources.
1. SDK - 16.0
2. SD - S132
3. Board - NRF52 Development kit.
4....
hardware: nRF9160 DK 0.8.2 firmware: 0.7.0-29.alpha
I want to send data every a few seconds through MQTT. It fails in the first and second Tx after MQTT client initiation...
Hi there,
I am having a hard time with some C pointers to add a new BLE Characteristic.
I would like to have a function that returns a simple characteristic metadata and...
Hi , I am using nrf52840 dk with zigbee cli example in sdk. I have configured nrf52840 as coordinator. I am using xbee pro s2c modules as router in zigbee network. Terminal...
Hi everyone,
I want to send my IMU's readings through BLE to a central. I have implemented the code and notify the central every 1s with the measurements.
I have an array...
Bonjour, je ne peux pas télécharger un firmware via l'application nfr toolbox avec mon Huawei p8 pour mon home trainer connecté, via bluetooth. Je reste bloqué à 2% et un...
I'm working on a solution and facing a few difficulties. well, I have more than 100 smartphones (android and iOS) devices in closed proximity were all the devices are logging...
Hi,
We have an embedded flash of 4Gbit which stores sensor data. The data needs to be transferred to a Smartphone. Now we are using USB cdc acm for transferring data with...
SDK 16.0
52810
S112
From the sample code of SDK we can see that the UART is enabled by code ourself, as the following. However, what's the usage of the NRFX_UARTE_ENABLED...
