I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Where can I find documentation of http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.0/nrf/samples/nrf9160/serial_lte_modem/README.html#serial-lte-modem IP UDP low power...
Hi, I am trying to create a custom_service for my application.
I am using nRF52832 SDK_16
SES
I want to create the BLE_SERVICES
which has send characteristics and...
Hi,
I converted ble_app_beacon example to Segger Embedded Studio (using version 4.30b), as per the instructions in the link https://infocenter.nordicsemi.com/index.jsp?topic...
I configured a NRF52832 with non-scannable and non-connectable as well as scannable/connectable advertising. Everything is working fine.
But I want to fully understand the...
I have an existing phone app (using the traditional GATT system), and I would like mesh-enable my products so that if the products can see each other, then the phone can connect...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
Hello,
I'm trying to setup an automated pairing for two devices. My peripheral device is advertising and should only allow connection requests from a specific central device...
I'm developing a multirole device to connect to a peripheral device that we developed earlier.
The multirole device when acting as a central device it scans for the peripheral...
To the kind attention of Nordic support team,
1. I have been using secured gazell library, where master is always polling in order to receive a message.
I was wondering...
Hi!
I'm developing a TCP server running on th e nRF9160, but there seem to be a problem with accepting clients. The code is very simple, just calls to socket, bind, listen...
Hi. I've developed a PCB with nRF52832 and I'm having problems with the circuit. When I put my hands closelly of P0.00(XL1) and P0.01(XL2) the bahavior of nRF changes... I...
I apologize if this was already answered elsewhere - I didn't find it.
I have been digging in the nRF52840 source code for the serial_nRF52840 SES project to understand...
Hello, I am trying to switch from BLE_GAP_PHY_AUTO to BLE_GAP_PHY_CODED in runtime, and I need to change central event length via sd_ble_cfg_set(). Whether is it possible...
