Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi,
i am begginer, using my nRF52832 DK with ble_app_uart as peripherial, which is connected to PC via J-link (usb cable). I want is to establish serial communication between...
Hi,
in DFU error occurred and showing as [DFU] Remote DFU error: Insufficient Resources in the log.
Chip Used NRF52810
package size is 53.8 KB
is there any restriction...
Hi,
I just got a ppk2 and I am not sure which wire needs to be connected to where.
I am going to use this to measure current consumption but I've used only extarnal DUT...
Hi all,
I'm starting a project with a nRF52840, and start protoyping with pca10056 board.
I started with compiling ble_app_blinky example app, with armgcc.
I can compile...
My nRF52 device has a connection opened in peripheral mode and in some cases I want to close the connection with reason code "power off", i.e. call sd_ble_gap_disconnect with...
Hi,
I'm reading through the documentation on using the SAADC with the NRF52 kits. The examples are using PPI to manage the SAADC and allow it to sample locationally in...
Dear All,
I need a high frequency clock in order to measure the time between a couple of events. In the RTC HAL there are functions that allow to retrieve the counter...
nordic nrfconnect sdk, wrong bit mask in driver for thingy light sensor bh1749
In the nordic nrfconnect sdk there is a bitmask typo causing wrong anction.
The header...
When running firmware without a probe, interrupts don't seem to work. I'm using a Segger Mini Edu on an Actinius Icarus (nRF9160). I'm using EGU1. When the probe is attached...
Hi,
I am looking for detailed electrical characterization details for SAADC - beyond 1 page summary in nRF52833 product spec v1.3; under 6.21.10.1 SAADC electrical specification...
Is there some documentation listing what C library functions are supported? For example if I use the Keil IDE to look for FILE I find it. But if I look for 'fread' it says...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
