Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I am trying to change the radio Tx power in nRF5340. I'm using Zephyr HCI RPMsg for the network core. The datasheet says it should support up to 3dBm. However, the Zephyr...
In the soft device documentation (html) the message sequence diagram for Btle Stack Enable calls sd_ble_cfg_set twice with the same set of parameters. Is this a mistake? The...
Hi All,
I am developing a custom BLE profile for my current project and several of my characteristics are write/notify characteristics. I am finding that when I write...
Hi there,
I just started using Embedded Studio (v5.10d on Windows 10, nRF Connect SDK version 1.4) with nRF52840dongle and nRF5340 PDK. Here is what I did
1. Copied...
Hi, I am developing a new project in which I will use NRF52810. I read in the datasheet that it is possible to configure NRF52810 in LDO and DC / DC regulators mode. My application...
Hello:
Looking at the different demos (applications and samples) available for nRF9160, I noticed that some of them generate multiple hex files while others, only few...
Hi,
I have bootloader programmed in nrf52840. Using OTA I programmed one application region but that application stuck after bootup.
Now how to recover from this situation...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
getting error in running bootloader
Output/secure_bootloader_ble_s112_pca10040e Release/Obj/nrf_dfu_validation.o: in function `nrf_dfu_validation_init':
I have designed a custom board with the nRF52840 following the examples from the dev kit, dongle, and datasheet (circuit config 5). The board is similar to the dongle but...
