Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I can't figure out why but my build cannot locate files that are included in the makefile.common
I'm using SDK 5.1.0 and the ble_app_hrs project. It seems it can't find one...
My device is smart watch. We transfer some data to phone and receive notification from phone over BLE.
My question is those two functions(connect_params_init and sec_params_init...
Hello
I'm new in the world of nordic semiconductor and I've a little problem. I would like to transfer ANT+ data of a HRM Garmin in serial protocol to my PC. I use a nRF51422...
Hi,
I transmit a data packet to AP2, i wonder if it needs a sequence for resetting or not while AP2
initializing.
And, I send a packet data to AP2 by UART(AP2...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
