I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hi, support team
I need to realize two-wire uarte receiver(with low power), in the scenario there is no data come from TX in most time, so after receiving the data I need...
SDK: 15.3.0
BOARD: custom nRF52840 pre-product
Hi, I want to implement usb dfu trigger library.
but, faced with a problem.
My project are started from usb cli...
cli_agent_router and multi_sensor example with nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 nrf52840
problem: The coordinator restarts occasionally, and the zed cannot rejoin until...
Hello,
I am trying to configure the SAADC for the NRF52810. I read that I have to enable it via the sdk_config.h. Here I find an entry for:
NRFX_SAADC_ENABLED - nrfx_saadc...
I have two related questions about nRF52 (nrf52832) which I have not been able to pinpoint from the documentation.
Can the 32MHz crystal connection be replaced by...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...
Hi,
I have a low level mcu (128 kbyte flash) connected via UART to the nRF52840.
My current flash usage (text output arm_gcc) is about 256 kbyte + the softdevice.
Since...
I am somewhat of a beginner - I have successfully built and programmed a "Hello World" example on the nRF5340. However I am having trouble building some of the Bluetooth samples...
So I am using the Mesh SDK in version 4.0.0 and 2 nrf52DK boards with some custom software running on the boards, but derived from the light switch examples. The boards work...
