Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
Hi
i m using Bmm150 magnetometer sensor. i m trying to read x y z values. However, im not able to obtain the correct magnetometer values. I'm getting 0000 as values in all...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
PLease, could anyone provide me a code exaple on which i can learn how to use sd_flash_write & sd_flash_erease ? I tried to use them but keil give me this : .\_build\nrf51822_xxac...
Hello Dev Zone.
thanks for watching mt ask.
I need help.
I have 2 question.
1. I need use saadc continuous sampling
in SDK example, is it continuous Mode?
...
For RAM locations, I've looked at the getting started guide that discusses using debugging to find the RAM address. https://devzone.nordicsemi.com/nordic/short-range-guides...
I know one of nRF52840 SPI instances supports direct DCX signal drive but I can't seem to find any mention to this feature in nRF52832 so I am assuming none of its instances...
Hi Sir,
As check the ref. schematic of CKAA, the pin count shows 94.
But in the below table shows the pin count is 93
Is there a typo in the datasheet (V1.1)?
...
We are using nrf52832 and S132 Softdevice. The app starts from 0x26000 and we want to change to some other location may be from 0x27000. We could see that SD is using the...
Hello !
is possible turn off my system using sd_power_system_off when the Watch dog is enabled?
After I called sd_power_system_off my device is restarting and initialize...
I can not find where to change the default pins to connect the nrf52840 to the rpi over SPI. The default pins are SPI pin Raspberry Pi pin nRF52833, nRF52840 or nRF52811 pin...
I have begun using V1.2.0
It seems that I'm no longer to enter AT commands.
I've also tried the AT Command sample and get the same issue.
No problem connecting through...
Hello,
I am adapting the 802.15.4 wireless UART example from the nRF5 SDK 15.3 to also make scans and associate with a PAN coordinator. However i am having trouble with...
I have a time-sensitive block of code run purely by the CPU, not within any interrupt handler or peripheral. Part of the execution is getting interrupted, and so what I would...
I am testing DA7212 with my nrf52840 and i have made connections but i am not sure if thats right. Also i am trying to use i2s loopback example from sdk.
i need some gu...
