hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
Hello
I am working on SDK v17, using nRF52832 (MDBT42Q) and MPU6050 sensor. I tried TWI_SCANNER because I thought there was a problem getting the value of MPU6050.
However...
I am reading a thermistor voltage divider from Vdd using the SAADC with a reference voltage of Vdd/4 and gain of 1/4. I thought that this would track Vdd so I wouldn't need...
Hi, the provisioning works and after that the dk is capable to get mesh messages but oddly enough a restart brokes this feature.
The error message is:
0x0c means BT_HCI_ERR_CMD_DISALLOWED...
Trying to install nrfutil on a system with Python 3.9 but it only installs the old version 5.2.0 which is broken on Python 3. This is the last version before the version check...
I use the internal LFCLOCK to drive my application. Sometimes, I need a more accurate clock to do time measurement. At startup, I can start the external crystal oscillator...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We built 2 configurations for...
I’m using nRF52810 in my design and for BLE communication I want to use Data Length Extension (DLE). Currently I’m using SDK v 15.2.0 , S112 and since DLE cannot take place...
Hi,
I have a very strange issue on my nRF5 development kits and dongles. Whenever I load the softdevice and firmware to the DKs or dongles. After sometime, the USB connection...
when I use central and Peripheral all concerned, Eight Peripheral connected to the central 。when I'll connect my phone to the central Peripheral . Device Error
Here's the...
Hello,
I am using a nrf52 DK in an educational context.
For this reason, I am not using the SDK, but implement basic features on a lower level.
I used the implementation...
I would like to confirm that the temperature measurement is sent from the end-device to the coordinator using the example zigbee temperature sensor.
I'm looking at Testing...
With the introduction of mesh_config_file_clear() in 4.2.0 the behaviour of mesh_config_clear() was changed such that only a subset of all the file ids handled by the Mesh...
