Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
When we test the BLE conducted power, we find some phenomena, when IC power is setted to 0dBm, the active power loss is similar with passive path loss, it is consistent with...
Hi,
I would like to save my project and add something like a version number to it. I use an example from nordic SDK. So in my case I use solution from ...\examples\ble_peripheral...
Hi Guys,
I am trying to enable LESC Encryption, but I do not understand how to generate keys_own.p_pk and DH keys.
The sequence is the following:
1. I receive BLE_GAP_EVT_SEC_PARAMS_REQUEST...
Hi,
We want to implement periodic advertisements on nRF52840.
We use:
1) nRF5 SDK ver 16
2) Softdevice S113 ver 7.0.1 (but this can be changed if required)
Does...
I am looking into automating the programming steps for the nRF9160 and nRF52832 for a production environment. I would basically like to do what the nRF Connect Programmer...
There seems to be a bug in the mesh stack friendship code: the friend node times out infinitely when an LPN node is re-provisioned with the same address.
Steps to reproduce...
Hello everyone,
I'm working with a nrf52840 devboard on which I put a LIS2DH12 accelerometer. I had a perfectly working example program featuring multiple functions. My...
Hi all,
I'll explain the problem. Our device (that uses a nRF52832) works with a custom app developed for iOS (v 13.4.1) and we've a custom set of services/characteristic...
Hello,
I'm trying to add DFU updates to a target board connected to a power profiler as a part of our CI process.
I have a nRF52-DK programmed with connectivity firmware...
Hello,
I'm getting err_code BLE_CONN_HANDLE_INVALID after calling ble_cps_measurement_send
I thought ble_cps_on_ble_evt was handling all of this but seems not.
I...
Hi
Use SDK15.3 path .. \ .. \ examples \ dfu \ secure_bootloader \ pca10040_ble \ arm5_no_packs. Using fstorage to write flash data, the function nrf_fstorage_write returns...
Dear Nordic Team,
I use a custom dev board with the nRF52832 SoC and the nRF5 SDK v16.0.0.
I need CoAP functionality for my project. I managed to get the CoAP Examples...
Hi guys, I am developing an mqtt-based app using board nrf9160. I tested the mqtt_simple example but it does not work. Here is my setup.
+ Broker server: test.mosquitto...
Hi, I'd like to set the alarm state of a minimal power configuration cluster that only has the attributes "remaining battery percentage" and "battery alarm id". However the...
