In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
HI there,
I wanted to use nrfx spi with nRF5 SDK 17.0, but it was removed. I checked that in nRF5 SDK 15.3 it should be available, but when I downloaded it the example is...
Hi Everyone,
Last two weeks I'm trying to make a Real time streaming custom service on PCA10056 DK. I have modified the ble_image_transfer code according to my requirement...
I'm testing the Zigbee CLI Agent example and try to read info from my Titan wall sensor. I can read almost all info, but not values, that are using float type.
How I can...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk-psm-current-too-high-after-opening-and-closing-a-tcp-socket/260026#260026 , however they said...
I have been looking at the Mesh library for BLE communication and wonder how much work it would be for me to use the same library for a long range 2,4 GHz radio?
Is the...
Hi,
now we use SDK17 "ble_app_hids_keyboard" example, we found after the moble phone connected to the ble keyboard, if the ble keyboard power off and power on ,the phone...
I am trying to to do adc reading from external 9V Litum battery.
In the PS document, I know nRF52832 can read adc until VDD(3.7V ???).
Then, in my case, do I have to design...
Hi,
I use the timestamp log in SDK17, and I find the time will auto clean at about 1min6-7sec.
Below is the code init the log.
/**********************************...
Hello,
I have a setup containing an NRF9160 communicating with another chip over UART at a 1M baudrate.
The following code is currently used:
I have configured the...
Hello team,
Greetings From Deepa. I need an manual installation procedure and building, compiling and Running the zephyr -OS with my laptop for learning purpose. I browsed...
I'm using nRF52840, PCA10056, and finding that if WDT is enabled (but not expired), after a soft reset (NVIC_SystemReset, or a debugger reset) the RTC no longer runs.
If...
