Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello! I would like to use a predefined example from the nRF SDK and instead of the board's button, to use an external stimulus (let's say, an external button ). Similarly...
Hey,
I am working on the nRF51 DK and nRF51822 with SDK12,S130, trying to pass a SIG PTS test for required IOPT, however always getting the same "INCONC" verdict, the PTS...
Hi,
I am trying to interface IS25LP064A External Flash with nRF52832 using SPI. I want to get the device ID/ Manufacturer ID of the flash. I am able to get the same in Arduino...
Hi everyone,
I'm using the nRF5SDK160098a08e2 and i tried to compile the ble_app_eddystone exampe but i'm getting this compilation error!
cannot find ../../../../.....
I am unable to read any uart input when I configure UART1 with nRF9160DK.
Please let me know if anything is wrong in my code/config
main.c
nrf9160dk_nrf9160ns.overlay...
In the Sleep mode and nrf52810 was Broadcasting with space 125ms once.
The normal temperature was good,that only 0.08mA. but why not 85℃，The current was up to 0.21 mA ,it...
Hello
I would like to detect timeout when I send a confirmable coap message not received.
My problem is that the response I receive in my response_handler is always...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
Hello, everyone.
I use the ble_app_uart on the nrf52DK board and SDK V17.
I would like to send data from the app using RX characteristics of UART service. The function...
Hi all.
I have written an application using a softdevice and I want to analyse an interesing behavior I don't understand at the moment. So I want to record a trace/log of...
