Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs
but:
1.How does the client receive those data?
2.How dose the client send data to server...
I'm totally new to Nordic, ARM development, and the mbed platform. Not new to embedded development however.
So far I can't get the simplest possible program to run.
...
I just received my nrf51822 dev kit and noticed that the SWD debugging cable will only connect to the PCA10004. The PCA10005 that came with my kit has pin 2 missing, rather...
HI,
I wrote my application based on "MasterEmulator->ProximityDemo" for testing device with nrf51822. My device have to switching between Gazell and BLE stacks so all the...
Hi
In ble uart project, the data is used string format. Now, we want to modify uart apps to tx/rx binary format. Could you tell us how to modify the uart apps? Thanks.
...
I added a local service with a characteristic with the Notify permission set.
On the device I'm connecting from to the nRF8001, I can see my custom characteristic has a 0x2902...
I'm designing what is essentially a small beacon board built around an nRF51822. On the antenna outputs I've used the discrete component balanced to unbalanced circuit shows...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
