In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I'm currently porting a project to nRF5 SDK17. Some time ago we decided to use the nrfx module as a fork of https://github.com/NordicSemiconductor/nrfx .
So I synced...
I'm working on a switch device using nRF5 SDK for Thread and Zigbee version 4.1.0 on an nRF52840 on a PCA10056.
I can get my device to join a network, and can see that the...
I see that Apple finally played their card in the consumer asset tracking device space last week. the "Find My" network will be available to third party devices. Details are...
Hi,
I'm working on the Basic example Blink_led.
I would like to change from LED 1 to LED 2. I changed the ch0-pin = <3> in the nrf9160_pca10090_common.dts but now the...
I would like to implement firmware update of nRF52832 through UART from Linux SoM, do you recommend following the DFU procedure or implement custom bootloader? I don't need...
I am using the 9160DK (0.9.0) and testing the PSM and eDRX modes with ncs V1.3.0. if I program the Asset_tracker without any changes I can connect to the nRFCloud.
from...
Hi
Unsopperted device. The detected device could not be recognized as neither JLink device nor Nordic USB device
I believe nRF connect programmer can't fint nRF5340...
On reviewing Zephyr SDK V1.3.0-rc1
I am able to build and run the soc_flash_nrf example as a nrf9160dk_nrf1960 board all works as expected.
when I try with nrf916dk_nrf9160ns...
Hello!
I am working with the nRF9160 devkit and I have encountered an issue.
I cannot seem to properly enable PSM to use the GPS and LTE at the same time.
In the application...
Hello, For our project we were planning on using a 3rd party module MS88SF2 (nRF52840), which schematic snapshot is provided and which will be powered though the li-po battery...
Hi guys,
I am using the Nordic nrf52832 board for my project. One of my goals is to enable the device to read the voltage from the external source. I have already found...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
I am trying to do Mesh DFU.
I have done updating ble_app_blinky successfully for the 1st time over mesh but after that, I tried to do again by increasing the application...
Hello,
I am working on a custom board using a nRF52840 based module. I am using SDK 14.2
I am running the following simple code to sense when an GPIO goes to a low state...
