Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi!,
I am trying to use one of the analog inputs for reading the voltage using saadc.
Since a don't have a battery now that is about 3.5V or less, I decided to use one...
Hi, I am trying to create a custom board and add it to the zephyr app. Currently, I have added boards/arm/irnas_izoramv21 file to my application folder. When I am building...
Hi
I am using nRF51822, S130, SDK12, Working on adding static key security to my application
So far I have change the GLS (glucose) example to static passkey and connected...
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
