I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello,
For clarification I use the nrf5_SDK_for_Mesh_v2.1.1. and the nrf52832.
I'm trying to scan for Ibeacons in which I need to get the UUID, major, minor, and the device...
Hello,
I have intention to use NRF52840 as HW peripheral just for communications over BLE. It means, it will be connected to the main MCU and provide interface for utilizing...
I am using nRF52840 Dev kit (PCA10056) , with nRF Mesh SDK 4.0 and nRF SDK 16.0 .
I have such FOUR kits . I have been able to modify vendor model for a sensor to transfer...
Hello everyone.
I'm a fresher of programming nRF52833. I'm doing an application for my final project in my university. What I need is get the RSSI in order to analyse the...
Hello -
I am evaluating nRF52840 to replace the Bluegiga BLED112 in an older product. I am surprised to get very low range from the nRF52850 USB dongle, barely 10-15 feet...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
Hi Nordic team
I tried AWS FOTA and Nordic FOTA at nrf connect for cloud. It did work well.
We now want to set up our own cloud. It's neither AWS cloud nor nrf connect...
Hi,
Sorry for the newbie question but how am I going to use the SAADC to measure 4-20mA current loops? I've used the SAADC to measure temperature, voltage, and resistance...
Hello !!
We are using nRF52833 MCU in our one of project. It is very cost sensitive project. We are proving supply to MCU from coin cell CR2032 battery. Also we enabled...
Hi,
I'm currently developing custom board with nRF52832 and I'm experiencing weird issues.
It's mostly related to BLE, especially on Samsung A series devices (A3, A7,...
