We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I want to make serial connection in between an nRF52833 and a LPC1752.
When I use the UART in a firmware without using the SoftDevice for Mesh 4.0.1 , everything is working...
Hi,
I am using a Linux Host to communicate with my nRF52840 as a USB CDC ACM device. As a test, I ran minicom and was able to transfer bytes to my Nordic app successfully...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
I have a device with no OS on it that talks serial through a UART to a nRF53840. I need to be able to update the nRF53840's firmware across the serial link, but since I don...
Hello, I am working on the BMD-300 Series Evaluation Kit with nrf52832 microcontroller and I tried accessing the serial number of my nrf52832, with these functions:
m_device_id1...
One doubt, if a node gets reset or disconnected , due to power failure in openthead cli mesh, dose it need to get configured again to join the mesh or will it connect to mesh...
First, by "Custom Protocol" I just mean that I need to directly access the radio to transmit or receive single packets occasionally. The literature appears to indicate that...
Hi, We flashed an ncs v1.3.0-rc1 build onto a 5340 DK network core, and ever since then the UART is not sending any data to our PC. We have connected RxD and TxD to pins P0...
I've seen a few discussions on C++ support. It's frustrating I can't contribute to the conversation - I'm not sure if that's because my account is too new, or if comments...
Good day, support!
I have a couple of questions regarding the mandatory services of the nRF52840 dongle.
1) How to add characteristics to the mandatory services 0x1800...
