We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all !
I have been working on an nRF51822 based board for a little while, the ten 1st prototypes worked well so we asked our factory to make 20 other with the same design...
Hi All,
Is the lite programmer which comes with the nRF51822 Development Kit sutable to program my code into nRF51822-Beacon?
If yes what cable would I need (supplier...
Hi,
I'd like to read PnP and the system ID from Device Information Service.
How can I initialize system and PnP ID? Are there any examples how to do this for nrf51822...
Hi,
I'm calling sd_ble_gatts_hvx and every once in a while I get an error code of 0x3401. I went through the SDK documentation but I could not find what that error code is...
Hi,
I have a peripheral device that needs to connect to both Android and iOS phones. Depending on which type of phone it connects to it is required to perform different tasks...
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
Hello!
I need more battery life and higher resolution in my applications. That's why i need to level down the signal power, if it is possible. Thanks in advance.
Hi,
I'm using nRF51822 Bluetooth Smart Beacon Kit. Is it possible to to switch between
beacon mode and configuration mode without the need to press SW2 button e.g.: by...
How do I keep advertising when I have a connection come in? I'm a BLE peripheral.
I'm running SD 7, is there a particular flag or sequence I need to do now that I've upgraded...
Hey!
I'm testing out the new SoftDevice and am trying to update firmware OTA but thus far have not been able to do so. I've tried from the Master Control Panel android...
I'm using NRF51822 as SPI slave and STM32 as SPI master. Everything works fine except the first SPI transaction after resetting both boards.
On the first transaction I...
Hi guys,
I'm curious whether or not i can try the mbed platform on the EK board. The circuit of the mbed kit and the EK look pretty similar. All the LEDs and buttons are...
I'm using the NRF51822 - I've just started a project. I can build and load it into my target board. I enter debug mode, and I'm able to do step through the code, add breakpoints...
What are the iROM and iRAM settings for the v0.5 S130 softdevice for the nRF51822?
The S130 softdevice spec sheet provides some clues, but no specific settings.
I've...
