Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I read from this news that it is possible to have wireless charging using nRF51822 chip.
www.nordicsemi.com/.../Nordic-Semiconductor-announces-Bluetooth-Smart-solution...
hi ,
Now, My program it have a crash when i to service discovery.
That always stop at when ble try to get the "PrimaryService(0x1801)" Characteristics
but i not found the...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Dear Nordic Support Team,
I am trying to write some information in the flash memory without success. In the ble_flash.h file, it is specified that the pages 0-127 are reserved...
hiii....
1.can any one tell where do we call advertising_start() function if we want to advertise after getting disconnect from a central device.
2.in ble_evt_dispatch...
I`m a newbie at Bluetooth Low Energy and Nordic Chips. I bought a DK for the nRF51822. I would like to set I/O pins over android and iOS application.
1.So what application...
Are there any common solutions to the issue of spi_slave.c using an array as its buffer? I would like to setup a circular FIFO, but I am not sure if there is any way to do...
We are using the S110 as a peripheral that emits data via notifications.
Is it safe for the central to also send characteristic writes while notifications are being emitted...
First of all ,i download the SD7.0 to my device, then i download my app to my device,in this case
my device's curent is 100uA.
First of all ,i download the SD7.0 to my device...
Hello,
i need some informatiorn about the layout of the nRFgo Motherboard. More specific i want to build a board which is connected to the ports P0, P1, P2; therefore i...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
