Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
This is a really basic question, but please bear with me. This is my first time foraying beyond the world of Arduino! :)
I'm attempting to make an ANT+ bicycle power meter...
I am using nrf52832,I have Defigned "CONFIG_NFCT_PINS_AS_GPIOS"as below。P0.09 is configed as POWER_HOLD pin, P0.10 is configed as buton.
I found that when I download softdevice...
Dear Members,
For scanning GSC10 sensor,
can this example be used ?
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ant_examples_scanning.html
Thanks
Hi,
I am currently working on the project that involves Pre-certified Bluetooth Module (SG Wireless SGW1110 CE & FCC certified, based on Nordic Semiconductor nRF52480)....
I am getting an intermittent "Softdevice assert: 151994:0" error on device initialisation or after the device has run for a period of time. I am using Light Switch Client...
Is there a way to generate a square wave like the one in the picture without using any kind of interruption to change settings middle-wave?
For example, the wave can be...
Hi,
I have been able to use the NRF-9160: Cloud_Client sample for sending data to my AWS IoT MQTT broker on PSM mode from my Thingy91 with a CLOUD_MESSAGE_PUBLICATION_INTERVAL...
Hello, I am trying to implement my own custom bootloader in the nRF52811. I have the softdevice loaded, which then jumps to address 0x19000. This is where I put my bootloader...
Hi,
I'm using nrf52833, flashed by using Jlink SWD programmer. I have no probleme to re-programmed 2/3 of my board.
But the hird gave an error. The strange things...
I am using the gazell protocol of nrf52840 to achieve some functions,but I don't know how to understand the protocol code deeply,anybody has advice or flow chart or relevant...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
When i start the nRF mesh app, it crashes immediatly. What do i need to do? I re installed it a couple times and i rebooted my phone a couple times.
The phone is a samsung...
Hi,
I am developing firmware both nrf52 and nrf91.
in nrf52, I activated BLE, usb and uart. Uart communication established between nrf52 and nrf91.
in nrf91, I activated...
