I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
I just received my Beacon Kit and need a programmer/debugger but money is tight. These are the options I'm looking at:
cut the traces on my nRF51822 EK board and add...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
Hi U guys
First I’m pretty new I use of bluetooth low energy, so bear with me.
It is pretty simple, I need to send a temperature each 10 sec. or whenever it has changed...
Hello. The nRF51822 Series Reference Manual says on page 38, "The SWDCLK pin
has an internal pull down resistor and the SWDIO/nRESET pin has an internal pull up resistor...
Tunning connection parameters to minimize current consumption for a fitness device transmitting data to ANT+ and BLE at 1sec intervals.
The desire is timeout after 60sec...
Hi,
We are trying to use the over-the-air bootloader in our application.
Our problem is the bootloader seems to require one first over-the-air download before it allows...
Which pins are mapped as ADC inputs for the NRF51822? I've pored over the documentation, but I can't seem to find which ADC pins (AIN0 to AIN7) correspond to which GPIO pins...
Hi
My aim is to be able to update the application code OTA in a 128kb chip (version nRF51822 QFABB0). First, I want to use the nordic original code to discard any other...
Hello all -
I'm trying to learn about the db discovery module from the perspective of the BTLE central and I'm a little confused by the client architecture. The SDK documentation...
I'm developing an application for a device which needs to support DFU service,
If my device get the specific packet over BLE (like 0xd1), i want to start dfu service. ...
I'm trying to study Message Sequence charts under the BLE GAP (Generic Access Profile) section of the s110 soft device.
However, I've noted that multiple links don't seem...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
Using: nRF51822-BK-FW (v 1.0.1).
From within, there is the source files for ble_app_beacon_bcs that when compiled/loaded on the beacon hardware, causes the LED to blink...
Hi. I have been trying to follow nAN-29 to migrate from Keil to Eclipse without success. I was excited to find the blog, devzone.nordicsemi.com/.../ . The blog suggests that...
