Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm trying to use the serial number of the nrf52832 microcontroller in code, how can I acess it with Segger.
I tried using this code from this link but it doesn't...
Hello. We are planning to change from QFN48 to WLCSP package in our product. However I could't find any guidelines to create the library for Eagle. I was wondering what is...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
SDK: 15.2 IDE: Keil SoftDevice: 6.1.1 Board: Custom Hello, I would like to synchronize an SAADC reading during a BLE transmit event. The power source to my board is a CR2032...
Hi,
I am developing an application for Thingy:91 in which I want to send data from the device to MQTT server. I am using 1.1.1 modem firmware and 1.2.0 ncs tag.
The whole...
I'm developing a product using an nRF52840 and an accelerometer.
I have created a Service with characteristic that sends accelerometer data over ble to the phone through...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever.I got an err_code NRF_ERROR_INVALID_DATA. Softdevice is s132nrf52611...
Hi,
I have a custom board with the nRF52840.
Is it possible to customize the DFU to be able to update the firmware through other interfaces than BLE or USB/UART?
I have...
Hi, I'd like to set up cccd here, but test the error,
In the routine nRF5_SDK_15.3.0_59ac345 nRF5_SDK_15.3.0_59ac345.0_59ac345.s.ble_peripheral?ble_app_uart/pca10040-s132...
Hi.
I have a RAK5010 i use for iot application.
i recently moved from SDK 15.20 to sdk 16. I use the task manager to manage two tasks:
1. task to dump nrf logs
2....
From section 5.2.1.11 I can tell that the peak current with CPU, TX, DC/DC, HFXO running the power consumption would be 8.6n mA. However, I could not find one that included...
Hi, we are developing a home automation product that needs to support ZigBee. However, at the same time I would like the devices to be able to work with a simple non-mesh...
Hi,
I have a question about bit rates of spis slave (Fspis).What is the minimum bit rates of spis slave? nRF52832 need to communicate with a mcu that it only can work on...
I used a translator. Please understand even if the sentence is weird.
Hi, I used nrf52832 QFAA. (RAM : 64kB, Flash : 512kB)
nrf-intel-hex enabled us to check memory...
