Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I have a Thingy:91 connected to a Garmin LIDAR Lite v4 (built on the nRF52840) via four GPIO cables. The code running on the Garmin reads one GPIO pin to signal a measurement...
Hello, I just want to clarify a secondary takeaway from my post:
https://devzone.nordicsemi.com/f/nordic-q-a/60714/best-approach-to-store-nonvolatile-data
I would like...
Hello.
I'm invesigating this on behalf of a customer.
I bought a thingy91 and wonder if it is possible to stream live video stream?
I would like to mont a camera to...
Hello everyone,
I have a Python script on my PC sending data through serial port COM5. I want to know if it would be possible to read the data sent from the PC on the nRF9160DK...
My target is porting my host MCU (STM32) to update my NRF52832 code through the serial.
I test it on SDK14.2.0 and PCA10040 , the secure_dfu_serial example is working ,...
Hello,
I experimented with some different capacitor tuning values at C1/C2; the external 32MHz clock initializes just fine for C1=C2=10pF, C1=C2=12pF (nominal), and C1...
hi ,
im try to add some consumer keys and system keys to the project:
nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and my code of hids_init...
Hello! I'm trying to reach zigbee on nRF52840, and I'm trying to get a zigbee communication from light_bulb. The hex file on the sdk goes in well, and I want to add additional...
I just learn nrf52840-Dk
I can download hex and build for example light_switch mesh to nrf52840.
But light_switch project have too many C files.
Which one C file or...
Hello !!
My hardware is based on IOT application. I'm using nRF52833 SOC as end node and powered it through CR2032 coin cell. In system ON phase ( sleep mode) it is consuming...
We are having problem in decrypting the AES 128 CTR encrypted key. The key is encrypted using the example project provided in NRF5 SDK16 {aes_ctr}. The following is what is...
Folks:
I´d like to know if there is a possibility to use RUST language to compile to nRF 52 modules ?
If so, where I can find any information about it ?
Also if...
Hi,
I change the configuration in proj.conf by adding
e.g.
CONFIG_SERIAL=n
It works .
However, I want to change similar things for the mcuboot_menuconfig after...
Hi,
I want to use Zephyr OS with openthread (I use Linux as a dev platform) and I thus have tried to modify the socket echo server to my needs (I am a noob with zephyr...
Hello,
I currently designing fault handling for a firmware for nrf52840 in SES for SDK16.
At line number 68 in the hardfault_handler_gcc.c, assuming a stack overflow happened...
