Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
hi,
ncs1.4.0\nrf\samples\bluetooth\peripheral_uart， The LBS service was added, but Advertising faile.
I don't know that I made a mistake in that step. It may be the address...
If I upload the pre-compiled asset_tracker file to the Thingy91, it works fine. If I compile it myself and try to upload it, nothing happens. It shows the write is successful...
I am trying to implement fstorage in my application using nRF52840, soft device 140, SDK for Mesh v4.0.0. and SDK 16.0.0 and Segger Studio.
Based on the fstorage example...
Hello,
I'm trying to develop a wearable stacking form-factor where number of boards can be assembled in a deck: MCU, sensors, actuators, power supplies, etc. Size of the...
Hi ,
I want to compile mesh examples .I tried it using segger ide Alternatively,I wish to compile it in cmake too. Can you please tell me the procedure to compile code using...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
Hi all,
I am using a nRF52840-DK as SPI slave with a MSP430 as host SPI master for a nRF8001 replacement application.
As I am absolutely not familiar with high level functions...
I am trying to communicate with a SH1106 OLED display using TWI and the popular u8g2 display controller library.
I've verified that the display works without problems on...
I am currently development an app based on the example from the experimental folder using a NRF DK52 as a relay between a central and multiple peripherals.
The app should...
Hello,
Happy New Year.
I'm not able to find nRF52840-QIAA-T or any replacement of this SoC available in the North American market.
I need atleast 5 SoC of the...
Setup: nrf52840 (without internal dc/dc), VDD = 3.3V
Assuming the VDD rail ramps up slowly, the nrf52 will start booting at it's power-on reset threshold of 1.75V (POR)...
Dear BLE Experts, I've followed this tutorial to create a custom GATT service and characteristic. The tutorial seems to be based on the BLE SDK , not the MESH sdk, hence the...
Hello,
Our company is kicking off a project (while we are at the very beginning stage) where multiple nodes (up to 1K) should be connected within a mutual network. I wanted...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
