I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
The nRF9160 datasheet tells the reader to refer to the website for Altium files. However, the only files I can find are for the development board. Is it possible to release...
What is the best way to change advertising data for each advertising packet in Mesh SDK's each of proxy / dfu / provisioner?
Using Mesh SDK 4.1, it would be ideal to be...
I have a working code which implements a UART peripheral written originally with SDK15.0
I would like to port it to the latest SDK 17.02
I can get advertisement and I...
Hello!
I have problem updating application firmware with the following message.
In nRF Connnect v.3.6.0 Programmer has been selected.
Log file indicated. INFO...
Hi,
We are trying to develop a wearable device that needs to sync time over a BLE connection and write the time to the internal RTC. We are using the nRF52832 for development...
Hi,
I'm experimenting a very high current during advertisement of the nRF52833. When using the "Online Power Profiler", it shows that I should expect peek current of around...
I'm attempting to use FDS on the nRF52840DK (PCA10056) with SDK V16.0 and SD enabled.
Per the documentation:
1) I register the callback function: fds_register(fds_evt_handler...
Hello, guys,
We are designing our custom board that contains nRF9160 SiP.
I would like to ask some questions here concerning programming/debugging nRF9160 SiP on the custom...
I am running my application on nRF SDK 16.0 and SoftDevice 7.2.0 but had this problem since 15.2 and 6.1.1 respectively. I thought it was resolved in an update since this...
Hello Everyone, I am using nRF52840 and i have 2 SPI slaves (Sensor and EEPROM), the sensor spi clock is use 10 MHz and the EEPROM is 40MHz, sck、mosi、miso、ss are all different...
Once I try to connect nrf52-dk development board to a personal computer, using a micro USB cable, once the USB is detected from the PC, it instantly reboot without any reason...
