Hi,
I’m streaming high-rate sensor data over BLE with an nRF52840 running NCS v2.9.0.
Data rate: 1 kHz, ≈ 8 400 B/s
Packing: 5 samples → 42-byte packet, pushed...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi Nordic Team,
I recently joined the DevZone and I’m interested in contributing to the blog. I’d like to write technical articles and tutorials related to Nordic products...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
I'm trying to build a prototype using the Adafruit nRF8001 Breakout and an mbed ARM CPU.
After Reset, I get a Device Started Event, telling me the chip is in Setup...
Hi,
In SD100v8, there is capability of checking the application version, to make sure no downgrade (or any other criteria required). The reference is in Link to SDK
...
There is a blog post for advertising but none for connection interval.
I am wondering how big is the difference for this example:
Measurement on peripheral every 4 seconds...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
Got stuck on an issue that has come and gone and then working fine, and are now back again.
I use a nrf51 module with the led-button-service example (sdk 5.2). It...
So, we are pretty far along in development (I have inherited the project) with an nrf51822, SDK 4.4.2 and SoftDevice "6.0.0-alpha". We are nearing release, and I was told...
I have set the POFCON to enable the power failure comparator and set the voltage level to2.5 volts. How do I know when the battery voltage is below the 2.5 volt level? How...
I want to try a UART communication without RTS & CTS
my board is PCA10001, and I use the SDK 6.1 example: uart_example.
I use Serial Port Utility to communicate with the...
Using SD_110 v6 I get a hardfault on the final call to sd_nvic_EnableIRQ(SWI2_IRQn);
sd_softdevice_enable before that returns success. Any idea why enabling interrupt could...
Hi,
I'm trying to implement an existing proprietary protocol on the nRF51422 SoC. In this protocol the device address is placed differently in the frame than the predefined...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
