NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi, everyone,
We develop BLE project including DFU bootloader.
But to use the standard bootloader "as is" it is not possible for us. Due to this problem we must make some...
On Apple platforms, It's pretty easy to end up in a situation where there is bonding information on the Nordic but that information has been deleted from the host. All you...
Hello,
I am using sd_power_system_off(); sfunction to put the MCU in sleep mode. I have to wake up events. One is NFC and the other is GPIO. Both wake up functions works...
Hello all, Nordic Team
i've a question regarding the format of the nonce used within CryptoCell Library v0.9.0.a
What i've learned so far is, that CRYS_AESCCMstar requires...
Hi
Is there any ready-to-use SDK example that demonstrates how the 2MPHY functionality is exercised on the nrf52810? We have gone through SDK15.0.0 but it appears that...
hello all,
i am developing with BLE_NUS.
i want to sent the string data on BLE using UART example.
string data length is over 300 bytes like belows.
55AA FFFF...
Hi guys
I am using SDK 13 and a nRF52, so on my application, I require a lot of RAM usage transfer small files in order of 10-30kB, is there way to see the RAM available...
i want to use the nordic nrf52840 in my new beacon design. however i dont see many others using it. i downloaded the DK files from nordic to figure out the feasibility of...
Dear Nordic Team,
Thanks for supporting. Now i want to integrate GPIOTE with BLE UART example. When i call gpio_init(); this function got error like below image.please support...
Good morning,
I am trying to get the lowest current during system OFF (no RAM retention, no wake-up sources configuration) on 52840 PDK. The spec says that the OFF current...
Hello,
i am working with a custom board, based on nRF52832, running the Bluetooth Mesh SDK v2.0; the board is equipped with a SoC that communicate with the nRF52 using the...
I am using the Windows version of nRF Connect v2.3.2. Aborting the DFU process does not work in the following use case:
- Connect to a nRF52832 advertising as DFU (for example...
I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection after disconnect For example...
Hello,
I am trying to fix the UART communication error(APP_ERROR_HANDLER(p_event->data.error_communication);).
I am sending a command(0x87,0x14,0x11,0x33,0x44) continuously...
