I'm building a project where I need to sniff bluetooth data exchanged between a Voltcraft SEM6000BT plug and my phone app. The idea here is to capture the BTATT (where the...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hello Nordic team, We are trying to use ST7305 display (custom driver that we have developed using st7789V as refrence ) and acconeer A121 senors on same SPI bus. The A121...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I am using the NRF54L15 DK for development. I have configured the i2c with P1.12 as SCL and P1.14 as SDA.
below is my code in .overlay file
Below is the code...
Hi,
(SDK 14.2, S140 V5.0-2.alpha)
I'm working on a ble project that includes to verify mac addresses.
For the Bluetooth SIG specs, when a device has a public adress...
I just update my sdk to 15.0.0, which use the softdevice s132_nrf_6.0.0. but when I try to generate the application package, I found the nrfutil do not give the sd-req code...
Hi,
Where the Firmware is being stored in the flash??
In which address of the flash the firmware is being stored when i flash the code??
In what file type ,the firmware...
Hi.
I am trying to set up a simple Ble beacon on a PCA10040 and a sniffer on another PCA10040.
IDE = Segger Embedded Studio for ARM (This works fine)
The beacon uses...
Hello,
I'm trying to start working with the NRF52832 Dev board for quite some time and can't manage to get anything complex done other than blinking an LED and even that...
We are using a TI AIC audio codec interfacing with the nRF52 over I2S.
The TI codec specifies the following expected clock frequencies for a sample rate of 16KHz and sample...
Hi
We are trying to find a solution to connecting a BLE peripheral to a "preferred" or "primary" central. We are considering having the peripheral connect to multiple centrals...
Hi,
Probably the answer to this question is no, but I can't seem to find any reference in the standard and/or your SDK documentation that proofs that the same relay message...
Hi,
In the Release Notes of SDK 14.2 the following issue (for an emulated NRF52810 project) is mentioned :
*** Known Issues
****************
** BLE **
- When working...
Hi,
Is there any API in Softdevice S132 v5 production to set up advertising extension?
In migration notes of SoftDevice S140 v5 alpha3 I can find annotation:
A new...
I have read the nAN24-13 application note as well as the crystal selection portion of the nRF24LE1 and nRF24LU1 data sheets and I am still undecided about this crystal
https...
Our intention is to wake up the nRFLEI from power-down using the external interrupts, perform some actions and return to power-down. There are three external control signals...
Dear nordic employee
when I use the spim to send 1 byte address to read it's value(4 bytes)
nrf_drv_spi_transfer(&spi,headerBuffer,(uint8_t)headerLength,readBuffer,...
Hi,
We are trying to transmit a single byte over SPIM using easyDMA but our logic analyzer shows that 16 bits are being clocked out. The first 8 are our message and the...
Hi
I just test the new sdk 15.0
When I test the power of the demo project named "ble_app_hrs_freertos", I get the power table below:
No chage
810uA
...