Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Hi,
We are using an nRF52832 with Soft Device S132 in a project. It has been requested that we should advertise as connectable with our own service and characteristics,...
Hi
In the NRF_MESH_PROV_EVT_COMPLETE event, I call
ERROR_CHECK(dsm_address_publish_add(m_next_unprov_address,&m_device_address_handles[m_next_unprov_index])); ERROR_CHECK...
Hello,
I want to be able to toggle blocking RTT output when using the log module.
Before in SDK13 I could just set SEGGER_RTT_CONFIG_DEFAULT_MODE to 2 in the sdk_config...
We are developing a system with multiple sensors that are spaced far enough apart that the furthest sensors won't be able to communicate directly with the user's device (also...
Hello everybody.
I just startet developing with nrf products and I'm facing a problem there.
I'm currently developing a System based on the ble_app_uart_c example. I'm...
Hi,
I am working on secure OTA in my custom Board which is having nrf51822.
I had done secure OTA successfully with SDK 12 but when i am trying to update the code using...
Hi, I want to measure Round Trip Time (RTT) varying data rate
However, when using coded phy, the RTT shows extremely long time
Using 1M or 2M with connection interval...
Our nRF52832 software detects the arrival of characteristics via writes from the Central and reformats the contents and sends them out in a UART message.
I've built an...
Hello, I want to create a simple example code with the leds ws2812b from neopixel from github.com/.../nrf51-neopixel. I need help to build the code.
Regards.
I'm converting an SDK 14.2.0 project to SDK 15.0.0 using the legacy functions and ARM GCC. It compiles OK but linking is failing.
The verbose output appears to be the Make...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
