Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello there,
I'd like to bond between two nrf5 modules and have a real time communication between them.
Now my question is what is the role each would have to play...
The nRF5 SDK is event-driven. So does it mean that the event handler in my application will be directly called in the interrupt service routine? If I write a long event handler...
Hi all,
I'm experiencing a performance drop with BLE proxy enabled in Mesh SDK 2.0.1 compared to Mesh SDK 2.0.1 / Mesh SDK 1.0.1 without proxies (higher packet loss, range...
Hi,
I have project for NRF51822 in IAR(EWARM). Short about project: it based on example BLE to UART communication; it uses SPI, I2C, analog inputs readings, some digital...
I used nRF5_SDK_14.1.0_1dda907.
I opened the bpwr channel then received ant+ packet.
The device received ant+ packet successful.
How do i know that how long time the...
hi all ,
how to build multi provisioneers with mesh network ?
i read some information and run the nordic mesh sdk 2.01 (ligh_ swith sample )
i have some issue with...
1. I am issuing a gatt characteristic (CHR1) write without the response requested from Central (BLUEPY/BLUEZ, Ubuntu 18)
2. Central than reads CHR2.
Is it possible...
Hello,
If I understand well, when the part of the flash reserved for the PM is full, new bonds cannot be saved until the application deletes older bonding data.
I would...
Hi,
I've heard some stories that that using analog capable pins for digital IO (UART in our case) results in significantly higher power consumption than using a pin that...
I've modified the app_timer library slightly to keep total system uptime, which I can use to keep calendar/epoch time if initialized with the current time from an external...
Hi Everyone,
I examined the document about nRF24LE1 FOTA "nAN18 - nRF24LE1 firmware update over-the-air". The document is about update firm by nrf24lu usb rf adaptor. I...
Hi,
I found some sensor drivers under nRF5_SDK_15.0.0_a53641a\components\drivers_ext\, like hts221, lps22hb and so on.
Where can I find example for those driver?
Regards...
Can someone please clarify a few things!
I'm trying to get high bandwidth on some to and from phone transfers. I have control and data gatt boxes, control has the connection...
Hi,
i am doing a project where i have to discover multiple custom services on connected ble peripheral from ble central device.
i am using nrf52832 with sdk 14.2.0 as...
