Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hi, I have decided to use Nordic Ble Mesh SDK instead of old mesh example. but I have only got NRF51 DK Boards. It was configured in order to use with NRF52 boards.
How can...
Hi @ll, I'm using Mesh SDK 2.0.0 with SD 6.0.0. The example everything is based on is the dfu-example (including parts of the beaconing example) I'm now trying to add a connectable...
Dear Nordic Team,
I have practiced the " ble-characteristics-a-beginners-tutorial" on DK board PCA10028, and it worked perfectly. Then I tried to change the user defined...
Continuing to port MESH into an IAR project. We would like to make logging work with IAR. Right now, we get a warning that the "format" attribute isn't supported.
Is there...
The valid master out time for <= 8 MHz is shown as tSPIM,VMO 59 ns. The valid master out time for > 8 MHz is shown as tSPIM,VMO,HS 8 ns. The latter tSPIM,VMO,HS could only...
In simple on/off example, the client can turn on several server nodes in the same group in the same time,
but in serial example mix simple on/off server, the info center...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
Hello,
So I'm loooking for a way to transfer relatively small quantity of data live as reliable as possible and as quick as possible between two nrf5 units and then between...
Hi,
I am using Nrf51422 DK, my need is to send file (which is placed in my computer)to the another nrf board. Tried with file operations (fopen,fgetc,etc.) in keil4. It...
While flashing program to nrf51822 device through terminal getting these error msg
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists,...
Hello, I currently using the proxy light switch exemple of the mesh SDK 2.0.1 in this configuration :
I search to have the less current consumption in the mesh client ....
Hi all,
Please find my following current measurement resuls in the pwr_mgmt example using a nRF52 preview DK and SDK 13
My setup is as follow:
SB40 is cut
SW6 is...
int main(void) { initialize(); execution_start(start);
for (;;) { (void)sd_app_evt_wait(); } }
can you explain me the execution of code flow in the main with these APIs...
