Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi all,s
I have a couple of nrf52840 boards and i was testing the ble mesh light application. The application works fine, but i changed it so it will periodically set...
Hi, I have tested thingy52-mesh-provisioning-demo in NordicPlaygound on github. It works fine by using a precompiled hex file (via nRFgo Studio) but It doesn't work (light...
Hi, I'm working on enumerating the 52840PDK as a CDC ACM device and I'm running into an issue where it's fully enumerating 80% of the time.
After doing some checking I've...
I'm working with TI's TAS2555 DAC as an audio output driven by the NRF52 via I2S. This DAC requires that the I2S clocks (MCK, SCK, and LRCK) are enabled prior to any data...
I understand that the next version of the mesh SDK will have the GATT proxy implemented. Even after reading the mesh profile specification the following is unclear:
- Is...
Hi,
our product is small tag, size of 70x35mm2.
Plastic covers are welded together and now looks like after welding some HW does not work properly. Flashing is successful...
Hello, I am running ble_app_uart_c example on nrf52832 IC. It is connecting to its corresponding peripheral and I achieved bidirectional communication.
The problem is,...
Hi! I am using SDK15 to develop an application for nordic chip which won't be using any kind of display nor keyboard input, so probably I'm gonna go for static passkey option...
I have and older board which is the PCA10028 with the nRF51422 chip.
I have downloaded the nRF5 SKD 15.0.0 and found there is not example DFU project for my particular board...
Hello
I am working on a project based on the Mesh SDK 2.0.1 light_switch example. The system is using SD 6.0.0 and PCA10040 boards. DFU is successfully implemented on the...
Hi,
I work on nrf52832 with the serialization.
The nrf52832 connectivity part is load with S132 V6.0.0 (uart hci).
The stm32 will communicate with the 52832 throught...
Hello, can you say me:
1) which Stack parts in Mesh SDK: nrf5_SDK_for_Mesh_v2.0.1 are implemented in harmony with Bluetooth Mesh Profile Specification and which are not...
Hi,
We are attempting to send data via BLE every 100 ms using an app_timer. The app_timer sets a flag and in the while loop in main.c we call
ret_code_t err_code; do ...
Hello, i'm currently doing my own DFU central for the BLE DFU on SDK 13, i followed all the steps on this link , i created the init and image files with nrfutil and now i...
I am trying to connect my Ubuntu machine with my nrf52 custom board my setup is as follows, Ubuntu machine --> FTDI USB2UART --> HCI interface of nrf52 I can see on my logic...