hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I would like to use SPI raw master library (used on application chip in serialization examples) in my own application.
First, to understand well SPI raw implementation...
Hi all,
is there any method to disable SWD in a way that every operation through SWD is blocked?
Do the MPU also blocks for reprogram the binary through SWD (maybe disabling...
Hello
I'm new in nRF51 SDK_11
In my tutorial I want to set a RedBearLab BLE_Nano nRF51 like Central.
I read the references in " developer.nordicsemi.com/.../a00066.html...
If I want to do a project following.
The central that has NUS service can connect to at least two peripheral .
Two peripheral also have NUS service.
I can receive notification...
Hi Guys, my project requirement is i have to make sure that my nRF8001 should bond with only one peer device. So i intend do a whitelist one peer device address, whitelist...
I'm trying to use 4 pwm by hardware
and 2 pwm by ppi.
It works pefectly purely.
and if softdevice included.
I have to change nrf_ppi_ to sd_ppi_ api.
and got no demo...
hi. As I know, if I want to change my nRF8001 Device name, I have to check "Over the air" and "From application controller with pipe" boxes in nRFGO Studio. in this case,...
Hi,
I want to make sure that the nRF52832 can start working (turn on) with a 1.8V power supply. Therefore I went to check the default value of POFCON register, in which...
Hi,
I got the PWM example code working, but I need only 3 PWM pulses (14usec on time and 34 usec off time). How do I configure the PWM pins to output just 'n' cycles? thanks...
Hello,
I have downloaded the nrf52 sdk (version 0.9.2) and following the steps listed here: infocenter.nordicsemi.com/index.jsp , to run the blinky led example. However,...
hi, i'm looking for layout and schematic (altium ver.) of attatched nrf module (nrf 51822 BLE).
how ans where can i get this ????
actually i need the imformation...
Hi,
For each sdk version there is a release note of known bugs which is good :-)
I guess it lists the bugs known at the time of the release of the sdk.
Are these posts...
Hello,
I am developing in NRF51 with gazelle communication. I specify in project setting (in IRAM) to use full RAM of my nRF51, and use MicroLib. My last working application...
Hi,
I wonder if anyone knows any free C++ compilers for nRF52. I tried the mbed but it is not fully supported for nRF52.
The regular GNU GCC: arm-none-eabi-gcc works perfectly...
We are working on a project using the nrf52832 (SoftDevice s332 v0.9.1alpha, nRF5 SDK 11.0.0) in which we build a library as a hex file and and load it into a known flash...
