nRF52832-QFAA using the LDO power supply mode，The firmware is configured to operate in the LDO power supply mode.The compilation and download processes are all fine.but the...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
May be I just did not fined a good reference manual for the software, but it really frustrating me to try and understand from examples.
Is there some guide which take a...
When P0.18 is configured as the RESETn pin, is there a pull-up enabled?
In our design we have an external CPU driving the nRF52 RESETn line.
We have a pull-down on that...
Hi all,
I was wondering if the information in the documentation is the right, I was looking for the Memory map for the nRF52 when using the SDK13 s132 v4.0.2, but on the...
Hello,
Could you please indicate where TXPOWER is defined in the "ble_app_beacon_pca10040_s132" code example ? If not defined, could you please indicate what is the best...
Hi,
we are currently planning how to productize our IOT module which is based on nRF52832. We most probably use pre-flashed SOCs, but the we should be able to read Device...
I am trying to implement 128 bit uuid service and charachteristic and I am getting error 4(memory error) from
line 10: sd_ble_uuid_vs_add(&m_midi_service, &midi_init); ...
Hello. Devzone engineers
I'm testing Nordic_Uart. I have some issues.
UART\s data not sent to android. Android app is nRFconneter and Example is nRF5_SDK_14.2.0_17b948a...
I'd like to be able to enable/disable the S140 SoftDevice multiple times during operation (SDK 14.2.0). To achieve this I'm using `nrf_sdh_ble_enable` and `nrf_sdh_ble_disable...
Hi,
Im trying to modify secure_bootloader demo in SDK_12.3, to use timers. I modify nerf_dfu.c file in libraries/bootloaders catalog. I want to achieve bootloader wait...
I am using MasterEmulator.dll for connecting to pear device.
I am using nRF51 Dongle and pear device is nRF52 custom board.
The pear device is advertising at very low...
Hello,
we have custom boards with nRF52832 chips, which show different behaviors in low power system ON mode. The current consumption is pulsing at around 22Hz to ~34Hz...
HI.
I purchased the nRF24LU1 + chip and created a USB Dongle module.
I have come to know about PID and VID.
Can I use nordic's VID (0x1915) as it is?
Is USB Dongle...
Hi ,Nordics
when I use my host device (reffered to the example of ble_app_hrs_c)to pair and bond with a peripheral device(a gamepad) ,the pairing failed .I don't kown...
Hello....
Is there a way to configure the SPI peripheral(s) to run at a custom bit rate (frequency)?... For example: Run SPI at 3.4MHz.. or any other custom frequency that...
Hello all,
Do you advise to have 2 SPI interfaces - one for the sensors we're using (accelero/ gyro) and another one for the SD card? if so, when adding an SD card to our...
