Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm trying develop on a custom board based on the nRF52832 and am running into some issues. When I run the blinky application (with no SD) the application executes fine. However...
Hi I'm developing beacon firmware using ble_app_beacon example code.
I was able to send good beacon data for my purpose. For the next step, I want to turn on the LED which...
Hi,
I am using a custom board based on nRF52 (nRF52832-QFAB-R) and programing it with softdevice.hex and "ble_hid_mouse" example application in the nRF5 SDK v14.2.0. the...
Hi,
I am using softdevice S132 V2.0 for nrf52832 controller.I am using BLE UART app. It is working fine on eval board.But when i checked it on custom board developed by...
Hello,
I am using sdk12.2.2 and nrf52. I have implemented fds_read, fds_write, fds_delete and its working as expected. Now when I am trying to use fds_update my data is...
We are trying \Nordic\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I want to control UART. If device is not in use i want to...
I'm just starting to bring up a custom board based on the nRF52832 and I am unable to program it using the J-link. It looks like my reset line gets stuck low when the JTAG...
Hi,
I work on the PCA10028 devkit with the nRF5_SDK v 12.3.0.
My project implements the ESB comunication concurently with the BLE by using the timeslot API.
I can send...
Dear Sir,
at the past I already ask this question at old forum, but now I can't find this ticket so I ask it secondary.
If I use a circuit configuration no.5 but USB is...
I lost several hours trying to figure out why my implementation of Queued Writes wasn't responding to write requests. Finally resorted to a line-by-line compare with the Experimental...
so it looks like there are no s140 iot examples available. My cursory investigation indicates this might be because L2CAP is not in the 140 softdevice.
I am currently interested...
Hi
I used nrfjprog.dll in our internal software. implementation is in C#.
Everything works just fine - except for the last call to NRFJPROGDLL_go - it seems like it starts...
I successfully ran the proximity_demo supplied by Nordic. I used my laptop's usb port to power up the device and it worked fine.
Then I unplugged my laptop and tried to...
